Washing Machine Motors – Common Problems Related to Washing Machine Motors

Washing Machine Motor is a device used for driving the clothes in the washing machine and induces the machine to run at a predetermined speed.

It runs with the help of the AC induction motor and this is powered with the help of DC to AC inverter. It is situated on the lower body of the machine and the motor forces the belt to tumble the wash tub. The motor is responsible for the tumbling, rotating and washing of the clothes. It is a double speed capacitor that helps in running of the washing machine in an open induction system.

The motor is empowered with running at a low, medium and high level based on the requirement of washing. It is also assigned with the operation of spinning and drying the clothes. The machine is installed in the washing machine in a horizontal way and it is built up with high starting torque. It offera reliable operation and easy maintenance. It can be used in a fully automatic machine and also in the semi-automatic washing machine.

Types of Washing Machine Motors

Some of the types are heavy duty, single phase, three phase and explosion proof motors. Those with overload protection offer long tenure to the washing machines. Heavy duty version is used for washing machine to work on high loaded power.

The machines runs tough and stubborn and makes the spin tub to rotate faster. Heavy duty versions are mainly used for high voltage consumption washing machines. Single phase one consumes low power. Single phase type can be used for washing machines having separate units of washing.

For example single phase version is used in spinning machine and dryer machine. Three phase type has strong power voltage and works easier on tough current connections. The electricity power is used in an enhanced manner in the three phase versions.

Common related problems

Washing machine motors face the problem of out of order due to the high voltage electricity and overloading of clothes in the washing machine. Overloaded washing machines force the equipment to move swifter with a harder action and this leads to motor repair. It often faces the problem of a squealing noise and this is caused due to the lack of lubricate oil. Sometimes the belt of the washing machines does not rest upon the motor promptly and this causes improper tumbling of the washer tub.

Defective lid switch also results in the non-movement of the motor. The breakage results in the slow working of the motors. The couplers are made out of rubber and plastic and there are many chances for breakage. Defective running is also a common problem associated with the washing machines.

Some helpful tips

The motors of the washing machine should be rehauled and services should be conducted regularly with the guidance of the professional service person. In the process of removal, the electrical connections relating to the washing machine should be disconnected to ensure safety.

It is always prone to burning out. This is caused mainly due to the frequent and continuous usage of the washing machine. Overloading of clothes leads to repairs and these can be rectified by adopting some small steps in this regard, basically by using minimal quantity of clothes for washing and another tip is the washing machine should not be allowed to run continuously for a long time. Intervals are needed and this makes the motor to cool down. It should be replaced in case of continuous problem. It should not be overheated and minimal usage per day should be adopted.

Best quality should be purchased and for this the best brand of washing machine should be selected. Motors should be used in a manner to provide a long life to the washing machine. Leaking of water in the spin tub should be immediately attended to and repaired, otherwise it may lead to spoilage.

Continuous spilling of water over the motor results in the burning of the same. All the functions relating to the washing machine is mainly connected to the motor. It is considered as an essential part of the washing machine especially in the process of washing and rotating of the spin tub.

Source by Zach Smith

LG Washing Machine, Front Loading Washing Machine

From washing machines to inverters, from mobile phones to air conditioners and from refrigerators to home theaters, LG is committed to make your life easier with its versatile range of products.

If you are looking for convenient, affordable, LG brings plethora of options to suit your requirements and budget both. Choosing a which would serve your needs perfectly is a task which requires a lot of thinking. You have to consider number of factors such as the price, durability, capacity, water consumption, requirement etc. Investing in good brand ensures you with the worth for the price you paid.

LG front load washing machine is designed with the unique combination of the style and technology to make your life easier. Some of its features are as:

• Inbuilt load sensor to take away your laundry load

LG front load washing machine is designed with an inbuilt load sensor which adjusts the wash cycle to give your clothes the perfect wash. With its load sensor, you can set the wash program at Fuzzy and it would sense the appropriate washing method required. It automatically detects the laundry load and a microprocessor which optimizes washing conditions such as ideal water level and time.

• Bio wash for stub born stains

LG washing machine also features bio wash which leads to maximum action of enzymes in the detergent and easily get rid of even stubborn stains like blood stains, chocolate stains etc.

• Crease care for wrinkle free clothes

This LG has a crease care feature to ensure you wrinkle free washing. After the spin cycle the tub tumbles which does not allow the clothes to stick to the walls of the tub. It helps in avoiding the formation of wrinkles on the cloth.

• Better rinse system to retain freshness

LG washing machine provides you better rinse as its rinse hold cycle gives the option of an additional rinse cycle to release the rinse hold before entering the spin cycle. It helps to prevent the foul smell and maintain the freshness of the clothes.

• Better care for baby clothes

It has baby care feature ensures all enzymes and bacteria are removed and no detergent residue remains in the clothes. Its gentle motor takes care of the quality of the clothes.

• Inverter Direct Drive Technology for saving energy and enhancing performance

These machines have the motor is directly attached to the drum without using a belt or pulley. Its lesser mechanical parts ensure least energy dissipation, minimal noise and enhance washing performance.

LG washing machine is designed to enhance your savings in terms of cost, energy and efforts. These machines are specially designed to make home maker’s life easier.

Source by Jayden Smith

Portable Table Top Washing Machines

The Science behind the Concept

The pressure washer operates in much the same way that any other washing machine does, just on a much smaller scale. The science of clothes becoming clean understands heated water sealed in an airtight drum. The heat makes the air in the drum expand and this increases the pressure, thereby forcing the detergent and water into the fabric of the clothes. Meanwhile the agitating activity encourages the dirt to be blown out. Many of the large washing machines work on much the same principle, although with some variation.

Limited Space

Laundry still needs to be washed no matter how little space you live in and, as a more attractive alternative than a visit to the Laundromat is the idea of ​​purchasing one of the portable table top washing machines that are now becoming more popular with today's modern apartment dwellers. Look hard enough and you can find quite a range of these particularly diminutive models on the market, some as simple as a bucket with an agitator while others, such as the Wonder Washer is worked by a handle and relationships on a build-up on pressure and the expansion of the warm water concept to clean your clothes.

Suncamp Portable

There are two models available, a twin tub that washes and spins clothes separately and a single tub that fulfills the functions of an automatic portable table top washing machine. The single tub has the capacity to take up to 1.5kg dry weight of laundry so despite the capacity is small, it works perfectly well, making it ideal for camping or RVs.

Washmax Washer

This is another of the portable table top washing machines on the market. This particular one can hand 1.2kg capacity of clothes per load. It is a proper lightweight, weighing just 5kg, and measuring 340mm high, 340mm wide, with a depth of 380mm.

Pyramid Portawash

This is a semi-automatic although there is also a twin tub version available. The automatic has a 10 liter drum capacity that is able to take just 600gms of laundry. The automatic weighs just 4.8kg, with the twin tub weighing around10kg. They are both tiny enough to hide away in a closet when not in use. The twin tub capacity can take more washing, as much as 1.5kg dry weight of clothes.

Malber WD 1000

Reports about this model seem remarkably varied; in fact, the only thing in common seems to be that this portable table top washing machine inspires quite strong emotions – people either love it or hate it! This small washer hooks up to the kitchen sink when it's in use and, to be quite honest, once you get used to its little idiosyncrasies, this is probably the worst you can say about this diminutive washing machine.

There are a particularly varied range of portable table top washing machines on the market, most of which are very good indeed. Some of these little washers are more robust than others while some some need you to operate them gently to get the best out of them – and do not overfill them. That said, if you put no more than the recommended load into any of these portable table top washing machines you will find that your laundry will come out of the wash at the end of the cycle beautifully clean and ready for drying.

Source by John Emdios

Choosing Washing Machines

Washing machines are now available in various designs and with special features that make them more and more consumer friendly. The earliest versions of washing machines were semi automatic which required personal monitoring. Later completely automatic washing machines were produced as a result of periodical up gradation of technology. The modern consumers look for appliances which can save time, energy and physical exertion in the process. Easier operation methods and zero maintenance costs are some of the advantages of latest washing machines. Even though completely automated machines are more convenient for the busy homemakers, many of them prefer semi automatic type as they are cheaper. Affordability becomes the sole criterion in choosing a home appliance for many consumers with shoestring budgets. Machines tend to become expensive when more innovative features are incorporated in them.

The semi automatic washing machines have two tubs. The first one is intended for soaking, washing and rinsing where the second one is used for drying. Once the washing process is completed, the clothes are to be transferred to the second tub manually. The process of washing and drying take about 45 minutes to one hour depending on the load. Even though it is a time consuming process many people are forced to choose semi automatic machines due to the basic cost advantage. Fully automatic washing machines with innovative features will cost 50 per cent to 200 per cent more than the semi automatic versions.

Washing machines are available in two styles. Top loading machines are generally cheaper. The advantage with front loading one is that it is more energy efficient than the top loading machine. Many modern machines are programmable. They can be set to the required schedules of washing. For example, expensive clothes like silk or wool can be washed under pre-set conditions. Water temperature, duration of cycles and detergent distribution are automatic. Combo machine which accommodate both washer and dryer are preferred by consumers for the efficiency and cost advantage. Heavily soiled clothes will be subjected to intensive washing process by regulating water temperature and the quantity of detergents. There are machines with facilities to pump in hot air to expedite drying process of clothes in cold and humid weather conditions.

Consumers have to take into consideration factors like space available and the expected workload while choosing a suitable washing machine. Size of the machines makes a lot of difference both in terms of cost and energy consumption. Normally a small family can manage with a machine which has the capacity to load 3 to 4kg of clothes. Machines of 8 to 10Kg capacity are available for consumers to choose from. Innumerable options are open for the modern consumers.

In a highly competitive market environment, manufacturers are striving to introduce innovative products. Modern machines are capable of monitoring the loads and automatically adjusting themselves much to the convenience of busy homemakers. Different temperature options, automatic detergent dispenser, multiple wash cycles and effective cleaning are ensured in the latest models of washing machines. Internet is a rich source to obtain valuable information about the products. It is advisable to choose a reputed brand with foolproof warranty and after sale service.

Source by Fredrick Joy

Most Common Problems on Smart Drive Washing Machines

The First Smart Drive washing machines by Fisher & Paykel came out of production in 1991 and since then we have experienced 8 improved and more sophisticated models. Although they differ a lot, the most common faults are very similar. From our long experience, we can say that almost 80% of them have minor faults, but are still worth repairing. We will try to cover all of them.If you find that yours is different, it may be some combination of few covered.


This fault can be caused by failure of one of the major electrical parts: motor, pump, rotor positioning sensor, reed switch, display panel or one of the water valves. Also, cause can be in the motor controller itself. It can be burned by water related short cut or by power surge.

On the “phase 4″( models 085, 058, 508, 608, 708) motor controller there is a mode where it can shut down in the event of a transient on the mains. What does this means is that machine will go in “asleep” mode and the module will not restart unless the power is turned off at the wall for at least 90 seconds.

On the “phase 5” (models 095-Fresh, 059-Pride, 509-Excellence, 609, 709) pump is considered as a part of the power supply. If it is disconnected (thermal cut out tripped which can be caused by pump blockage) washing machine will be dead.

Repair of this fault is quite expensive and vary between models from $100 to $250.

Best way to prevent it is to do regular inexpensive service checks of all major parts and empty pockets before wash. If you buy used washing machine try to arrange cleaning, water blasting and sanitizing services which will free drum and bowl from all dirt that can cause pump blockage.


This is most common washing machine problem and in some cases it is related to real technical issues and sometimes to misuse or wrong installation.

Easy to notice leaks are from water taps, inlet hoses, hot or cold water valves, water mixing chamber. Leak from top end of the drain hose is also easy to notice and usual spot is close to the connection to the body of the machine.

Leaking from the pump is almost always caused by poorly secured pump bracket; pump’s

diaphragm and pump itself are last causes for the leak. Next possible leak spot is an air bell.

If water level is not set properly and water is filled over HIGH mark on the agitator, splashing may cause some “leak”. Over filling may be caused by bad (dirty or punched) pressure pipe. Clothes overloading can make same problem.

Broken neck ring and damaged plastic inner bowl are another possible reasons for leak as well as too much detergent used.

Fixing of leak related problems should not(except damaged inner bowl and leak from main seal) be very expensive, up to a $100 most.


Noise can be related to few different sources, some of them indicating that machine have to be serviced or repaired to avoid major damage.

If washing machine is very noisy during spin cycle main seal and bearing are bad. This fault has to be fixed urgently, otherwise water leak can damage motor and rotor positioning sensor.

Banging sound is usually related to drain hose, inlet hose, mains lead or harness. They are either loose or washing machine has not been leveled properly. This can not cause some other bigger problem but could be very annoying.

Another banging sound can be caused by inner and outer bowl hitting machine’s body.

The reason for that is that water somehow escaped from two balance rings in the inner bowl. Same problem can be caused by overloading or uneven clothes arrangement in the bowl.

Pump can be source of very annoying noise. This noise starts on the beginning of the spray/deep rinse or spin cycle and lasts until pump empties water. It has been caused by rusted pump stator (water or humidity damage) or ex center rotor position. CRC spray will fix the problem temporary and new pump will save machine from more expensive faults(burned pump will burn triac on the motor controller).

Also cracked or chipped rotor magnets can cause some grinding noise.

To fix noise problem you may expect anything between $50 to $350.


First cause of this fault can be in reed switch(lid and off balance switch). Broken switch should be replaced to avoid motor controller failure.

Water taps can cause this problem also. Water should be connected and taps should be on.

If delay start is on, Strat/Pause switch will not respond.

When Auto Level has been used machine will resense water level every time the lid is opened.


This problem is related to the natural law. Usually standpipe height is too low. Minimum height should be 850mm from the floor. Top of the drain hose should be placed through “U” shaped hose guide not more than 2cm from the top of the guide. If drain hose is pushed too far into the standpipe or drain, washing machine will empty(siphon) water during fill or rinse cycle.

Siphoning can be caused also by restricted drain hose or partial pump blockage.

Source by Igor Ivanovic

How To Clean A Front Loading Washing Machine

There are two major types of washing machines, the top loader and the front loader. The top loading washing machine is the traditional type of washing machine that are found in most homes. They are called such because the bin where you place your laundry opens at the top of the machine.

On the other hand, front load washing machines were used before mostly for commercial purposes and these were commonly seen in laundromats. Unlike the top loader, the front load machine has a tub which opens at the front, thus the name. However, in the recent years, the front loader has gained much popularity and is now widely used in households.

No matter what type of washing machine you are using, you should give it ample care and maintenance. A previous article talked about cleaning a top loader. This time, this article is going to talk about the proper ways of cleaning a front loading washing machine. Here are some basic tips that will give you a better front loader.

Try draining it completely

Unlike top loaders which can be drained thoroughly, front load washing machines do not drain completely as the drain pipe in the latter is located at its side. With that design, some water is bound to be left inside the washer or tub. Sometimes, these remaining water may be the cause of that funky odor you have been smelling lately. To avoid this, try draining it out completely. If it does not drain out the hose, well, you can try draining it manually.

Let the moisture escape

Make it a habit to always leave the door to the washer open. Unless, of course, you are washing your laundry. Sometimes moisture is trapped inside and it causes the musty smell. Trapped moisture inside the washer is also a very attractive breeding place for molds and mildew not to mention germs and other harmful microorganism.

Use high-efficiency detergent

The kind of detergent you use is also very helpful in cleaning the front loader’s tub. No, I’m not saying that you should scrub the tub with detergent, that may cause in more lime deposits. Anyway, you should try buying high efficiency detergent, which produce less suds and less fragrance because of their high concentration.

Suds are a big factor to why you may have difficulty draining water out of the tub of your front loading washing machine. The detergent suds mix with water and make it thicker. Also, suds that are left inside the tub will harden and will cause lime deposits in the tub. Sudsy water may look cute and all but they cause problems. To avoid these problems, well, avoid the suds.

Wipe the inside of the tub

If you have the luxury of time, you can do this every after you finish doing the laundry. This way, you can be sure that the inside of the tub is really dry and that no detergent suds nor fabric conditioner remnants are there. There may also be some dirt inside the tub which came from your laundry. Clean these dirt and the like unless you want them mixing with your clothes the next time you do your laundry.

You also have to be careful in cleaning each and every nook and cranny inside the tub that may collect water and moisture. Even a little amount of moisture can lead to disaster. Remember, the enemy here are microorganisms. They are the ones to blame for dirty clothes and that musty smell. Clean even the hard to reach areas. However, if you cannot do this every after doing the laundry, you can try doing this twice a month. Then again, the more times you do it, the better.

Clean the drain pump filter

The drain pump filter is one of the parts of the front loading washing machine that receives the dirty work. Over time, you can only imagine how much dirty water and the like accumulated in the filter. Water that is never drained is still there, because where else would they go, right? Suds and all the other dirt filtered from the clothes are also there.

The drain pump filter, which is usually located at the bottom of the machine, can be taken by pulling out the drain plug. Remember to put a bucket or anything else that can catch water underneath the drain hose before pulling it out. Take out the filter and clean it. Doing this, you did not only clean the drain pump, you will also make the draining process faster without all those obstructions.

Source by Alan Cassidy

Magic Chef Washing Machine

One of the appliances that are dying out in the world, but where their parts are still heavily bought after comes in the form of a Magic Chef washing machine.

Magic Chef long since discontinued production of some of its more complex products:

  • Their washing machines
  • Their dish washers
  • Their tumble dryers
  • Their ovens

Since this has happened the amount of spare parts, new or scavenged from 2nd hand or broken down machines has been greatly reduced. This may not seem a problem for washing machine users, but as a piece of equipment they're the most likely item to break down.

You also have to consider that the majority of people that would purchase it are on lower imports because it's a relatively unknown as well as cheap brand. Being on lower imports, as well as the world being in uncertain economic times means that most are more more willing to want to try to get their machine repaired and not buy a new one.

Even though they're a cheaper brand their items can still cost thousands of dollars, and when money is tight people opt for reparation first. But this is no longer possible for most of the Washing Machine models out there simply because of the spare parts shortage.

Most people are only used to searching for what they want online and finding it straight away, but with Magic Chef parts you'll be starting a battle when you could be looking for weeks if no months for what you need. You've got to contact spare arts dealerships – and remember the whole process would mean that you would not have a washing machine to hand.

Source by Jonathan Octavius ​​Bell

A Normal Load of Laundry With Integrated Washing Machines Can Be Eco-Friendly

When buying integrated washing machines the consumer usually wants a space saving appliance that washes well. There are those who are under the impression a compact appliance does not have the same abilities as a large appliance. When it concerns integrated machines this is not the case. Integrated machines have a normal load capacity and normal wash cycles. This means you are able to choose an appropriate wash cycle. The cycle you use depends on how dirty the laundry is and the type fabric.

You may not know what load capacity is right for you. Two people would require a 4 kg load. Three people or more require a 7 kg load. Families may need a higher load. It is recommended you fill the machine at least eighty percent full for a wash. If there is a hand space width from the top when you push down on the laundry load it’s reached the required capacity for a full cycle wash.

Doing the laundry is a normal function and must be done on a regular basis. Washing machines tend to use large amounts of water and energy. You only have to think of rinses and spinning to realize how much. It is sensible to take advantage of the latest technology by choosing integrated washing machines that are designed to save energy and water. Such integrated washing appliances are regarded as eco friendly appliances.

If you choose to use eco friendly washing machines you will save money but you will also be helpful to the environment. There is a growing demand from consumers around the world for appliances to be both energy and water saving. Kitchen or utility areas fitted with integrated washing machines that are also eco friendly will be a draw card if you intend selling or renting out a property. Buying the right kind of integrated machines can be to your benefit.

Source by Susan E. Pritchard

What Are Integrated Washing Machines?

If you have been shopping around for a new clothes washer for your home, you likely have come across several integrated washing machines and have wondered what these were. There are several different kinds of units you can can choose from. Perhaps the most common style is the freestanding unit. Just as the name suggests, this style stands on your floor freely. You can also choose to purchase a stacked washer-dryer combo unit. These units include a connected washer and dryer stacked vertically. The other style you can choose from includes integrated washing machines. These units are designed to fit into your existing cabinetry and are equipped with mounting doors and sited controls.

Often, your laundry room will have a more upscale, high-end ambiance when you select the latter style. This style will give your space a cohesive look as your cabinetry will cover most of the hard edges of the machine, giving it a built-in look. You may think that this high-end look will cost you a high-end price. The truth is that you may need to pay a little extra to get cabinets built in to your laundry room if they aren’t already included in your space. However, beyond the cost of cabinetry, you can actually find a range of integrated washing machines with different features and prices.

Such machines are available in budget-minded models with less features as well as higher-end models with all of the bells and whistles you expect when you pay top dollar. Most newer models feature a quiet operation, and are available in sizes from 4-6 kg load capacity. There are both front loading and top loading machines available, and they are available in a wide range of colors, just as with other models. If you are looking for a more complete, higher-end look for your laundry room, consider one of these models for your home.

Source by Susan E. Pritchard

The How-To Guide on Using a Washing Machine

Believe it or not, there are many people that are not sure how to use a washing machine. This includes the types of washing powder and fabric softener to use and how much of it to put into the washing machine. The best part about living in the modern era is that most washing machines include the instructions to make your life easier.

In this instance, we are going to use a front loader as an example.

  1. First thing’s first – the sorting of your laundry. White or very light clothes need to be washed separately from clothing such as jeans, scarves and velvet. The reason why this is done is because certain fabrics lose colour after washing it multiple times.
  2. Next, you need to add the washing powder into the correct compartment. The washing machine will usually indicate which compartment it is using a small image. No more than a scoop or a small cup would be needed depending on the capacity and model.
  3. Fabric softener is a definite must if you prefer your clothes smelling fresh and feeling soft. Some clothes also look better when the fabric softener has been added.
  4. Now we need to turn the washing machine on so that we can pick the correct option for the type of clothing that has been loaded into the washing machine.
  5. The option you choose prior to starting the cycle would depend on the clothing that is inside the machine. The “Delicates” option should be chosen for small and fragile items such as underwear, thin t-shirts, and lacy jerseys that could be worn over evening gowns. “Duvets” could be bedding such as duvets, comforters and quilted blankets. Items such as jeans may also have an option that you can select that won’t damage the fibre.
  6. Some washing machines have the intelligence to determine the amount of time it will take to run the chosen wash so that you can plan your daily chores around that. This allows you to manage your time better at home especially if you are a parent or working professional.

If you are a working parent or busy professional, then you don’t have the time to run around for washing powder and fabric softener every month. So save time, buy wholesale and get the washing powder and fabric softener in bulk. This could also end up being a cost saving and time saving exercise for your household.

Source by Shabir S Joosub